一．适用：

本产品适用于棉布，化纤布，涤纶,针织，腈纶，牛仔，TC高弹丝毛衣料等高弹性各种服饰布料纺织品静电植绒工艺.

二．外观及组成：

丙稀酸树脂、乳白色粘稠膏状。

三．特性：

可不用过热，植毛效果牢固、不掉毛；手感柔软，节约人工、电费，节能环保；无毒无异味，安全可靠。配上1008固化剂可以达到低温固化的效果，具有耐磨，耐热，耐水，耐洗涤等特性。（双组份）

四．使用方法：

转移植绒工艺
1．植绒浆加助剂的比例为2%-5%；
2．助剂和主体浆搅拌均匀后，4-6小时内须使用完，调配时请计算好用量，以免浪费浆料；
3．根据面料要求，用80-100的网版印两遍，2-3次/遍，或丝印网版采用厚版印2-3次；
4．印好的图案约6-8成干，再进行转移植绒；
5．温度：150℃-180℃，压烫时间10-20秒，压力约6公斤（时间和温度可根据需求进行适当调整）；
6．正反面压烫后，冷撕热撕均可，洗水牢度测试请在24小时后进行；．植毛浆加助剂的比例为2%；
7．测试水洗牢度请在24-72小时后进行.（自然干燥时间与当天气温和空气湿度有关，请确认真正完全干燥后方可进行洗水牢度测试！）温馨提示：
1．上述资料仅供参考，一切以客户测试为准；
2．建议生产前请先做测试，确定后再大量使用，否则造成的后果自负.

Other detailed information

一．Substrates

This product is suitable for cotton,chemical fiber,polyester,knit,acrylon,denim,TC, high elastic silky fabric etc high elastic various cloth fabric and textile electrostatic flocking process.

二．Appearance and composition

Acrylic resin、milky white paste.

三．Characters

Free of overheating,the result of flocking is firm、do not shed, soft hand feel, cut artificial and electricity bills,energy efficiency and environmental protection,without poison, peculiar smell,safe and reliable. Compound with 1006 fixing agent can reach effect of low-temperature fixing,with characters of resistant to wear, heat ,water or wash.(two-component)

四．Usage

Transfer flock technology

1.The ratio of auxiliaries add into flock base is 2%-5%

2.After the paste and auxiliaries stir evenly,must run out within 4-6hours,on the process of mixing,should calculate the amount,avoid to waste paste.

3.According to the requirement of fabric,using 80-100mesh screen printing two times,2-3times/per time,or silk screen adopts rock table print 2-3times.

4.The pattern finished printing after drying 6-8degrees,and then make transfer flock.

5.Temperature,150-180℃,the time of press iron is 10-20seconds,the pressure is about 6KG(the time and temperature according to need to make appropriate adjustment)

6.After press iron two sides,cold tore and hot broke both OK. The test about wash fastness should be made after 24hours.(the time of natural drying is related to temperature and humidity of air,please make sure it is drying completely and make a test about wash fastness!)

Warm tips:

1.The above data is just as reference,everything stands on the customer’s tests.

2.Advising to make a test before production,after determined, in a batch production.otherwise,you should be responsible for results that caused by yourself.